Hair

How to ask your barber for a haircut

"A bit shorter on the sides" is not an instruction. Here is the vocabulary that produces the same haircut twice — guard numbers, fade heights, and what to stay away from.

4 November 2026 · 9 min read · By the STYVANTA editorial desk

There are two ways to get a good haircut. Bring a photograph, or learn eleven words. The photograph fails when your hair does not grow like the man’s in the picture; the words work almost always.

This is the vocabulary.

Start with the sides, because that is where the cut is decided

Barbers work in a fixed order: sides, then top, then the finish. If you describe the sides precisely, half the haircut is already correct.

Guard numbers. These are clipper lengths in eighths of an inch. Number 1 is 3 mm, number 2 is 6 mm, number 3 is 10 mm, number 4 is 13 mm. If you want 5 mm, say “a number one and a half” — most barbers will know what you mean.

Taper or fade. A taper leaves hair length increasing gradually from the neckline upward, and stops short of the skin. A fade goes down to skin at the bottom. Fades are more aggressive and grow out faster; tapers are more forgiving and last a week or two longer.

Low, mid or high. This is where the fade starts. Low sits just above the ear, mid sits at the temple, high sits well above the temple. High fades add apparent height; low fades keep the head narrow. If you have a round face, you probably want high. If you have a long face, low or a taper.

Blended or hard line. A hard line is a visible edge where the fade meets the longer hair. It reads sharper and more deliberate. A blended transition reads softer. Most contemporary cuts use blended sides with one hard line at the fringe.

So the complete sides instruction sounds like:

“Number two on the sides, mid fade, blended — no hard line.”

That is five seconds and it removes almost all ambiguity.

Then the top, in centimetres

Never say “a bit off the top”. Say the length.

“Four centimetres on top, point-cut the ends so it sits textured rather than flat.”

Length in centimetres is easier for a barber to honour than “short” or “medium”, because it survives the difference between your idea of short and his. Point-cutting is what stops a short top from looking like a uniform block — the scissors cut into the ends at an angle rather than straight across.

If you want volume, say so explicitly:

“Leave enough length that I can push it up — six centimetres, and don’t take the weight out of the front.”

The three sentences that fix most bad haircuts

“Square off the sideburns.” A rounded sideburn softens the whole face. A squared one adds a vertical line where there wasn’t one. It takes two seconds and changes the read of the cut.

“Natural neckline, not blocked.” A blocked neckline is cut in a straight horizontal line across the back of the neck. It looks sharp for four days and then grows into a visible dark band. A natural neckline follows the hairline and grows out invisibly.

“Don’t touch the hairline.” If you have any recession at the temples, the line-up is the fastest way to make it worse-looking. Ask them to leave the hairline soft.

What not to say

  • “The usual.” Unless you have been going to the same barber for three years and he writes things down, he does not remember.
  • “Like last time but shorter.” Shorter by how much, where, and starting from which length?
  • “Make it look thicker.” This is a goal, not an instruction. The instruction is “leave more length on top and take the sides tighter”.
  • “Whatever you think looks good.” You have just handed a stranger a coin flip and paid for it.

The photograph problem

Bringing a photo works if — and only if — the man in the photo has your face shape and your hair type. Otherwise you are asking a barber to reproduce proportions that were designed for a different head.

If you must bring a photo, bring two: the cut you want, and a photo of yourself with a cut you liked. The second one is far more useful, because it tells the barber what your hair does when it is cut well.

A test you can run

Next time, give the sides instruction with a number and a fade height, and nothing else. Do not say “shorter”. Do not point. Just the number.

If the result is closer to what you wanted than usual, you have found the actual problem: it was never the barber’s skill, it was the specification.

The version with your measurements in it

Everything above is general. The specific version — which guard number, which fade height, how many centimetres on top — depends on your face shape, your hairline and your growth pattern.

The face shape analyzer will tell you the shape for free. If you want the finished script, with the numbers filled in for your own proportions, that is what the report produces: one paragraph you read off your phone, in the chair, without having to think.

STYVANTA editorial desk

We publish our method, including the six measurements and the 240 styling constraints behind every report. If you disagree with the reasoning, say so — the method is here.